ultrasonic switch:



click here to enlarge schematic

parts:
　

　

Transmitter Parts:
IC1	NE555 timer IC
VR1	10k variable resistor
R1	4.7k resistor
R2	18k potentiometer
R3	1k resistor
R4, R5	220 ohm resistor
C1	680 picofarad capacitor
C2	0.01uf capacitor
D1, D2	1N4148 Diode
T1	SL100 NPN transistor
T2	SK100 PNP transistor
S1	SPST momentary contact switch
XMTR	ultrasonic transmitter 40-50khz

　

　

Receiver Parts:
RCVR	Ultrasonic Receiver 40-50khz
RL1	6volt 200ohm resistor
IC2	CA3140
VR2	250k Variable Resistor
R6	390k Resistor
R7	470k Resistor
R8, R12	15k Resistor
R9	12k
R10, R13	10k
R11	4.7k
R14	100k Resistor
R15	33 ohm Resistor
C3	0.22uf ceramic capacitor
C4	0.1uf ceramic capacitor
C5	560n ceramic capacitor
T3,T4	BC548 NPN Transistor
T5	BC558 PNP Transistor
T6	SL100 NPN Transistor
D3,D4,D5	1N4148 Diode

all resistors are 5 or 10 percent tolerance, 1/4-watt
all capacitors are 10 percent tolerance,
rated 35 volts or higher

The circuit described generates (transmits) ultrasonic sound of frequency between 40 and 50 kHz. As with any other remote control system this cirucit comprises of a mini transmitter and a receiver circuit. Transmitter generates ultrasonic sound and the receiver senses ultrasonic sound from the transmitter and switches on a relay.

The ultrasonic transmitter uses a 555 based astable multivibrator. It oscillates at a frequency of 40-50 kHz. An ultrasonic transmitter transducer is used here to transmit ultrasonic sound very effectively. The transmitter is powered from a 9-volt PP3 single cell. The ultrasonic receiver circuit uses an ultrasonic receiver transducer to sense ultrasonic signals. It also uses a two-stage amplifier, a rectifier stage, and an operational amplifier in inverting mode. Output of op-amp is connected to a relay through a complimentary relay driver stage. A 9-volt battery eliminator can be used for receiver circuit, if required. When switch S1 of transmitter is pressed, it generates ultrasonic sound. The sound is received by ultrasonic receiver transducer. It converts it to electrical variations of the same frequency. These signals are amplified by transistors T3 and T4. The amplified signals are then rectified and filtered. The filtered DC voltage is given to inverting pin of op-amp IC2. The non- inverting pin of IC2 is connected to a variable DC voltage via preset VR2 which determines the threshold value of ultrasonic signal received by receiver for operation of relay RL1. The inverted output of IC2 is used to bias transistor T5. When transistor T5 conducts, it supplies base bias to transistor T6. When transistor T6 conducts, it actuates the relay. The relay can be used to control any electrical or electronic equipment.
Important hints:
1. Frequency of ultrasonic sound generated can be varied from 40 to 50 kHz range by adjusting VR1. Adjust it for maximum performance.
2. Ultrasonic sounds are highly directional. So when you are operating the switch the ultrasonic transmitter transducer of transmitter should be placed towards ultrasonic receiver transducer of receiver circuit for proper functioning.
3. Use a 9-volt PP3 battery for transmitter. The receiver can be powered from a battery eliminator and is always kept in switched on position.
4. For latch facility use a DPDT relay if you want to switch on and switch off the load. A flip-flop can be inserted between IC2 and relay. If you want only an ?ON-time delay? use a 555 only at output of IC2. The relay will be energised for the required period determined by the timing components of 555 monostable multivibrator.
5. Ultrasonic waves are emitted by many natural sources. Therefore, sometimes, the circuit might get falsely triggered, espically when a flip-flop is used with the circuit, and there is no remedy for that.